Saltar al contenido · Skip to content
Leonida FM
Beta

Loading…

    Play GTA 6 on PC at 60 fps or more: capture card, Remote Play and low lag

    Reviewed 2026-11-19

    GTA 6 only exists on PS5 and Xbox Series, at 30 fps with no 60 fps mode. To watch it on your PC and raise smoothness, connect the console with a capture card (lowest delay) or Remote Play and add frame generation with Veyra or Lossless Scaling. Below: settings by graphics card and how to fix audio drift.

    The signal path, from console to screen

    Every hop adds milliseconds. Figures are Veyra community measurements (wiki, Nov 5, 2026), not ours.

    1. ConsolePS5 or Xbox Series. The game outputs 30 fps.33 ms base at 30 fps
    2. Capture card or networkHDMI into a USB/PCIe capture card, or Remote Play over your network cable.10 to 45 ms (capture card)
    3. PCReceives video and audio. The graphics card matters here.
    4. AppVeyra, Lossless Scaling or a Remote Play client: scaling and extra frames.+15 to 30 ms
    5. DisplayA 60 Hz or faster monitor. At 120 Hz there is less tearing.

    Pick how the console reaches your PC

    HDMI capture card (PS5 or Xbox)

    What you need
    A capture card with 10 Gbps USB or PCIe, an HDMI cable and a PC, ideally with an RTX card. Best format: NV12 at 60 fps.
    Latency
    2K 60 fps card: 10 to 16 ms; 4K 60 fps over USB: 35 to 45 ms; PCIe: 5 to 20 ms (Veyra community measurements).
    The good
    The lowest-latency route per the Veyra community, and the one that supports 4K.
    The catch
    It costs money and needs a 10 Gbps USB port or a free PCIe slot on your board.
    Sources: Veyra wiki: capturadoras · Veyra wiki: problemas · Veyra

    PS Remote Play or chiaki-ng (PS5)

    What you need
    A 64-bit Windows 10 or 11 PC, the same PlayStation account as the console and a fast connection (5 Mbps minimum, 15 Mbps better, per Sony). chiaki-ng is the free open-source client.
    Latency
    No official figure. The Veyra community measures 5 to 10 ms on a good network at 1080p; SmoovPlay's developer estimates 20 ms extra when generating frames at 60 fps.
    The good
    Nothing to buy. Veyra and SmoovPlay embed the chiaki-ng core.
    The catch
    The picture is capped at 1080p and compressed, so it blurs in motion. Game Rant warns that input delay is noticeable.
    Sources: Sony: requisitos · PlayStation: Remote Play · Sony · chiaki-ng · Veyra wiki: consola · Notebookcheck · Game Rant

    Xbox app, Greenlight or Veyra (Xbox)

    What you need
    An Xbox Series X|S with remote features on, a Microsoft account and at least 10 Mbps (Xbox). Greenlight is an open-source client for home Xbox streaming; Veyra describes its Xbox support as unofficial and experimental.
    Latency
    Not verified: we found no latency measurements for this route with GTA 6.
    The good
    No capture card, starting from Xbox's own app.
    The catch
    Less documented than the PlayStation route. Xbox Cloud Gaming is not a valid route here: no source backs it for GTA 6 on PC.
    Sources: Xbox · Greenlight · Veyra · PCMag

    Your graphics card, your setup

    Pick brand, series and route: the selector gives you the app, the settings, what to avoid and the expected latency, each with its source.

    Brand, series and route

    Brand
    Route

    Use Veyra · GeForce RTX 40

    On an 8 GB 4060, Veyra's guide asks you to lower noise reduction to 1080p or even 900p.

    Veyra fit: Good fit · Driver: Smooth Motion available, but do not enable it for Veyra.

    Settings, in order

    1. Download the NVIDIA or AMD package of the latest version from GitHub, extract it into a new folder and run veyra_qml_ui.exe. Start with every effect off, check picture and sound, then switch them on one by one.
    2. Capture at 60 fps, not 30: per the Veyra community, at 30 latency doubles (about 90 ms versus 40).
    3. NV12 format (P010 only if you use HDR). Avoid MJPEG: it is compressed, adds delay and hurts the picture.
    4. Capture card on a 10 Gbps USB port or PCIe. A 5 Gbps port used as if it were 10 drops frames.
    5. On the PS5, turn HDCP off and set the video output to the right resolution (do not feed 1080p and let the app fake the rest).
    6. Pro Mode, Frame Gen tab: multiplier 2X for 60 fps.
    7. Noise reduction (NR) at 1080p or 1440p and, if you use it, with the input locked at 1080p: each layer costs 20 to 30 ms and frame generation alone 5 to 10 ms.
    8. Close MSI Afterburner and GamePP, and in the NVIDIA app turn off RTX HDR, Smooth Motion and RTX Dynamic Vibrance for Veyra: they cause over 90 % of crashes per the guide.
    9. Against tearing: monitor at 120 Hz and VSync on inside Veyra (the author: "just turn V-Sync on"). If output stays below target, check for a wrongly set frame cap.

    Avoid

    • Smooth Motion and NVIDIA app filters over Veyra.
    • Capturing in MJPEG or at 30 fps.
    • Stacking several noise-reduction layers at native resolution.

    Expected latency

    Capture card at 60 fps about 40 ms (10 to 16 ms in 2K, 35 to 45 ms in 4K over USB), plus 15 to 30 ms for Veyra: about 70 ms end to end in the community's measurement, on top of the 33 ms inherent to a 30 fps game.

    Sources: Veyra wiki: problemas · NVIDIA RTX 40 · Veyra wiki: ajustes · Veyra wiki: capturadoras · Veyra

    AMD versus NVIDIA at a glance

    Graphics cardVeyraDriver frame generationRecommendedSources
    Radeon RX 6000ExperimentalAFMF 2.1 supported (driver 25.3.1 or later); not verified over video windows.Lossless ScalingAMD Fluid Motion Frames 2.1 · AMD FSR 4.1 · Veyra wiki: problemas · Lossless Scaling
    Radeon RX 7000ExperimentalAFMF 2.1 through HYPR-RX; not verified over video windows.Lossless ScalingAMD Fluid Motion Frames 2.1 · Veyra 2.1.2 · Veyra wiki: problemas
    Radeon RX 9000ExperimentalAFMF 2.1 through HYPR-RX; not verified over video windows.VeyraAMD Fluid Motion Frames 2.1 · Veyra wiki: problemas · Veyra 2.1.2
    GeForce GTX 10 and 16Not recommendedNo Smooth Motion (RTX 50 and RTX 40 only) and no RTX Video (RTX only).Lossless ScalingNVIDIA Smooth Motion · NVIDIA RTX Video · Lossless Scaling · Veyra wiki: problemas
    GeForce RTX 20Not recommendedNo Smooth Motion (RTX 50 and RTX 40 only). RTX Video: RTX.Lossless ScalingNVIDIA Smooth Motion · Veyra wiki: problemas · Lossless Scaling
    GeForce RTX 30LimitedNo Smooth Motion (RTX 50 and RTX 40 only).VeyraVeyra wiki: problemas · NVIDIA Smooth Motion · Veyra
    GeForce RTX 40Good fitSmooth Motion available, but do not enable it for Veyra.VeyraVeyra wiki: problemas · NVIDIA RTX 40 · Veyra wiki: ajustes
    GeForce RTX 50Good fitSmooth Motion available, but do not enable it for Veyra.VeyraVeyra · NVIDIA Smooth Motion · Veyra wiki: ajustes

    Step by step with a capture card or Remote Play

    1. 1

      Pick the route: HDMI capture card (lowest delay) or Remote Play (nothing to buy).

    2. 2

      Set up the console: PS5 with HDCP off and the right output resolution; for Remote Play, turn it on in Settings, System, Remote Play.

    3. 3

      With a capture card: console HDMI into IN, OUT to the monitor and USB into a 10 Gbps port. In Veyra pick Capture Card, your video device, 60 fps and NV12 format.

    4. 4

      With Remote Play in Veyra: enter the console's IP, your PSN account ID and the 8-digit pairing code; press Pair, Save and Connect.

    5. 5

      In Pro Mode, Frame Gen tab, set the multiplier to 2X to reach 60 fps.

    6. 6

      Close MSI Afterburner and GamePP, and turn off RTX HDR, Smooth Motion and RTX Dynamic Vibrance for Veyra in the NVIDIA app.

    7. 7

      Line up sound and picture with audio compensation and check the result with a stopwatch.

    Sources: Game Rant · Veyra wiki: problemas · Veyra wiki: capturadoras · Sony: requisitos

    Latency and audio drift: what really ruins the experience

    The game runs at 30 fps and frame generation improves smoothness, not response. Here is what you can actually trim.

    Add up your latency

    Frame generation

    Setup delay: 35 a 56 ms

    Plus the 33 ms the game carries at 30 fps, which no app removes.

    Community reference: about 70 ms end to end, with 40 ms of capture at 60 fps and 15 to 30 ms from the app.

    Estimate adding ranges measured by Veyra users on their own hardware; yours may differ. Not tested by us.

    Where the time goes (ms, community measurements)
    • Capture at 30 fps90 ms
    • USB 4K at 60 fps (NV12)35 a 45 ms
    • Capture at 60 fps40 ms
    • Veyra: noise + frames15 a 30 ms
    • USB 2K at 60 fps (NV12)10 a 16 ms
    • Frame generation only5 a 10 ms

    Sources: Veyra wiki: capturadoras · Veyra wiki: problemas

    Cable on the console and the PC

    chiaki-ng recommends putting the console on Ethernet; Sony asks for at least 15 Mbps for Remote Play. With a capture card the network is out of the signal path, though it still helps the console. On the PC, a shared 1 Gbps network card stuttered under load.

    chiaki-ng · PlayStation: Remote Play · Veyra wiki: consola

    Wired controller

    Sony asks for a USB cable to connect the controller to the PC with Remote Play. With a capture card the controller connects to the console: there is no published wired-versus-wireless measurement, so we promise no gain (not verified).

    Sony: requisitos

    60 fps output cap

    The game runs at 30 fps and the 60 is interpolated. If Veyra reports output below target, first check for a wrongly set cap or sync, then lower scaling. Its 2.1.2 tests measured with 60 and 120 caps.

    Veyra wiki: problemas · Veyra 2.1.2

    Vertical sync (VSync)

    It depends on who generates the frames. AMD's AFMF requires VSync off in the driver and in the game. In Veyra, its author recommends turning it on against tearing. Do not mix them: pick a single generation layer.

    AMD Fluid Motion Frames 2.1 · Veyra wiki: problemas

    Fix audio and picture drift

    If sound arrives before or after the picture, it is picture delay the audio has not compensated. In five steps:

    1. 1

      Check that sound plays through the device named after your capture card (not the headphones or the monitor) and that the app's audio source is that card, with "Listen" enabled in Windows.

    2. 2

      In Veyra, try the "A/V sync" switch (automatic sync). If the sound lands 1 or 2 seconds late, switch it off: some users get it right with compensation off.

    3. 3

      Set the audio compensation (professional mode) by hand until they match. Calibrate with a stopwatch in front of the console: send the capture card's output to a monitor and photograph the same count on the monitor and in the preview; the gap is how many milliseconds to delay.

    4. 4

      The less picture delay, the less to compensate: capture at 60 fps in NV12, a single noise-reduction layer at 1080p and 2X generation (the app adds 15 to 30 ms to the picture).

    5. 5

      If you record or stream with OBS instead of the app: in Advanced Audio Properties, "Sync Offset" delays the sound in milliseconds; step up by 100 and re-record a short clip until it lines up.

    Sources: Veyra wiki: problemas · Veyra wiki: capturadoras · OBS (Volume101)

    The scaling and frame layers, one by one

    LayerWhat it doesRequirementOver a console captureSources
    VeyraFree, open-source (GPL-3.0) Windows 11 app: it takes the signal, improves the picture (scaling, denoising, HDR) and generates frames (2x, 3x, 4x or dynamic). Works with a capture card, PS5 Remote Play, PC to PC and screen capture.Windows 11 x64 and DirectX 12. NVIDIA or AMD package depending on your card; its guide recommends RTX 30, 40 or 50 and treats Radeon cards as experimental.Built for this. It drops duplicated frames before generating new ones (PC Gamer), so true 30 fps becomes interpolated 60 fps.Veyra · Veyra wiki: ajustes · Veyra wiki: problemas · PC Gamer, vía Yahoo Tech
    Lossless Scaling (LSFG)Paid Steam utility (6.99 dollars on its page) that scales and generates frames over any window. LSFG 3 has a fixed mode (multiplies) and an adaptive mode (sets a target) plus a lighter model for modest cards.Works across a wide range of hardware and ships a separate generation model for low-power GPUs.It sits over the Remote Play or capture window. Duplicated frames make it stutter: PC Gamer suggests using scaling only over a Remote Play stream.Lossless Scaling · PC Gamer, vía Yahoo Tech
    AMD Fluid Motion Frames 2.1 (AFMF)Frame generation inside AMD's own driver, no game support needed. Requires Adrenalin 25.3.1 or later and VSync off, both in the driver and in the game.DirectX 11, 12, Vulkan and OpenGL games; Windows 10 and 11. HYPR-RX turns it on in one click on RX 7000 and newer.Not verified over a capture-card or Remote Play window: AMD documents it for games and no source validates it over video.AMD Fluid Motion Frames 2.1
    NVIDIA Smooth MotionNVIDIA driver frame generation: one extra frame between two real ones, switchable per program in the NVIDIA app.GeForce RTX 50 and RTX 40; DirectX 11, 12 or Vulkan games.Do not enable it for Veyra: its guide documents that NVIDIA app filters (RTX HDR, Smooth Motion) injected into Veyra make the GPU vanish or crash the program. Over other windows, not verified.NVIDIA Smooth Motion · NVIDIA RTX 40 · Veyra wiki: problemas
    RTX Video Super ResolutionNVIDIA AI upscaling for 360p to 1440p video, meant for supported browsers and players.GeForce RTX.It targets video played in a supported browser or player; no source validates it over a console capture. Not verified.NVIDIA RTX Video
    AMD FSR (upscaling)AMD upscaling. FSR 4 launched in 2025 exclusive to the RX 9000; FSR 4.1 reached RX 6000 in October 2026. Veyra and Lossless Scaling ship their own FSR options.Radeon RX 6000 or newer for FSR 4.1 in games; in a video app it depends on the app itself.In-game FSR does nothing here: GTA 6 does not run on your PC. Only the FSR built into Veyra or Lossless Scaling counts.AMD FSR · AMD FSR 4.1 · Veyra · Lossless Scaling
    Radeon Anti-LagCuts input lag in PC games. Anti-Lag 2 needs the game developer to integrate it.Radeon; enabled per game profile or with HYPR-RX.Does not apply to GTA 6: the game runs on the console, not on your Radeon. Not verified over the capture window.AMD Anti-Lag
    SmoovPlayFree app that embeds the chiaki-ng client and generates AI frames over the PS5's 1080p video. Its developer estimates 20 ms of delay at 60 fps and more at 90 fps.Windows and a stable connection; they recommend GeForce RTX 30, 40 or 50. Not tested by us.PS5 Remote Play only. Capture cards are listed as experimental.Notebookcheck

    Keep reading

    Everything we have on the launch, each with its source.

    GTA 6 news

    The latest on the launch, each story with its source.

    Frequently asked questions

    Can you play GTA 6 on PC?

    Not natively: the game launched only on PS5 and Xbox Series and, as of November 19, 2026, no PC version has been announced (Kotaku, Nov 18: not announced yet). What you can do is watch the console on your PC through a capture card or Remote Play and improve the picture with an app.

    Why does GTA 6 run at 30 fps with no 60 fps mode?

    Rockstar targets 30 fps on every console, PS5 Pro included, and there will be no performance mode: its technology production director explains that not even the PS5 Pro's processor, slightly better than the base console's, can run the game's simulation at higher frame rates.

    Are 60 fps with frame generation real?

    They are interpolated: the game still produces 30 images a second and the app creates one in between. It looks smoother, but response to the controller stays at 30 fps plus the delay of your setup.

    How do I fix lag with Remote Play?

    Put the console on Ethernet, use 1080p, get at least 15 Mbps and check that the PC's network card is not saturated. If it still drags, a capture card has less delay than Remote Play, per Game Rant.

    Does Lossless Scaling work with GTA 6?

    It works over your capture or Remote Play window. Over a Remote Play stream, which already duplicates images, frame generation can stutter and PC Gamer suggests keeping to scaling.

    What graphics card do I need?

    For Veyra, its community guide recommends a GeForce RTX 30, 40 or 50. With a GTX, an RTX 20 or a Radeon, Lossless Scaling is the broadly supported option. Use this page's selector for your case.

    My audio is out of sync with the picture. What do I do?

    Turn on Veyra's automatic sync or, if the sound lags, turn it off and set audio compensation by hand against a stopwatch. In OBS, Sync Offset delays sound in milliseconds.

    Source

    Spoilers: hidden

    Back to GTA 6 guides · Fan-made site, not affiliated with Rockstar Games or Take-Two Interactive.

    Matrícula de adorno: la fecha es la única parte real.Decorative plate: the date is the only real part.